Description

POWER SOURCE VTD24SA: VTD-SA Series 24 V DC Switching Power Supply Product Description

Brand and Product Identification

The POWER SOURCE VTD24SA is a VTD-SA series single-output AC-DC switching power supply manufactured by ETA Electric Industry, Co., Ltd., also referenced as ETA-USA. The VTD24SA model identifies a 24 V DC output unit within the 100 W VTD-SA converter family. The front panel and packaging carry the Power Source and VTD Series markings, and the unit is marked as made in Japan. The VTD-SA series includes VTD05SA, VTD12SA, VTD15SA, VTD24SA and VTD48SA models for different output voltages.

Product Function and System Role

The VTD24SA converts single-phase AC mains input into a regulated 24 V DC output for industrial control, instrumentation, automation, communication or electronic equipment. It provides a stable DC supply for PLC I/O, sensors, relays, control panels, motors drives auxiliary circuits or other 24 V DC loads. The power supply is a fixed-output switching converter, not a charger, UPS, inverter or isolated safety supply; its role is to convert AC line power into regulated low-voltage DC for connected control electronics.

Input Specifications

The VTD24SA nominal input voltage is AC 100 V, with a DC 130 V rating. The input range is AC 90 to 132 V, or DC 110 to 175 V. Input frequency is 50 or 60 Hz, with an input frequency range of 47 to 440 Hz. The supply is single-phase. Maximum inrush current is 20 A at rated input and output, measured at cold start. Typical efficiency for the VTD24SA is 85 percent according to the VTD-SA specification.

Output Specifications

The VTD24SA output voltage is 24 V DC, and rated output current is 5.0 A, giving a nominal output power of 120 W within the 100 W class converter family. Output voltage adjustment range is plus or minus 10 percent of rated output voltage at no load within the input range. Maximum output ripple and noise is 290 mV peak to peak. Line regulation maximum is 192 mV, load regulation maximum is 216 mV, temperature coefficient is 0.03 percent per degree Celsius, and drift maximum is 135 mV. Dynamic load regulation is typically 720 mV, with recovery time typically 0.5 ms. Rise-up time is a maximum of 100 ms at 25 degrees Celsius and rated input and output. Hold-up time is a minimum of 20 ms at 25 degrees Celsius and rated input and output.

Protection Functions

The VTD-SA series provides overcurrent protection with current limiting and automatic recovery. Overvoltage protection shuts down the output when the overvoltage threshold is reached. Remote sense and remote on-off functions are not available on this model. These protection features help protect connected DC loads and the power supply during overload or output fault conditions, but the supply should still be selected according to load current, duty cycle and environmental conditions.

Environmental and Electrical Ratings

Operating temperature ranges from 0 to plus 50 degrees Celsius. Operating humidity is 85 percent relative humidity, non-condensing. Storage temperature ranges from minus 20 to plus 85 degrees Celsius, and storage humidity is 30 to 85 percent relative humidity, non-condensing. Withstanding voltage is AC 1500 V for one minute between primary and secondary, AC 1500 V for one minute between primary and frame ground, and AC 500 V for one minute between secondary and frame ground. Isolation resistance is a minimum of 50 MΩ measured with a DC 500 V insulation tester between primary, secondary and frame ground. Leakage current is a maximum of 1.0 mA.

Mechanical Construction and Cooling

The VTD24SA is a convection-cooled enclosed switching power supply module. Typical switching frequency is 71 kHz. Typical weight is approximately 690 to 750 g, with listed product weight around 0.72 kg or 700 to 740 g depending on source. The module mounts in equipment or a control panel, with input, output and ground terminals on the terminal block. Vibration and shock ratings are specified for non-operating transportation conditions in the VTD-SA datasheet.

Typical Application Scenarios

Typical uses include 24 V DC supply for PLC control panels, industrial control relays, sensors and transducers, instrumentation racks, communication equipment, small automation machines, vending or process equipment, and replacement of older Japanese or industrial DC power supplies. The VTD24SA suits low-power DC electronic systems where a fixed 24 V, 5 A regulated supply is required and the AC input falls within the 90 to 132 V range.

Installation and Wiring Notes

Installation and wiring should follow the VTD-SA datasheet, local electrical codes and the supplied equipment instructions. Confirm AC input range, output voltage, load current, ground connection and terminal polarity before energizing. Mount the unit with adequate convection clearance, keep primary and secondary wiring separated, and connect frame ground according to safety requirements. Verify output voltage under no-load and rated-load conditions during commissioning. Use appropriate fusing or protection for the primary and load side according to system design.

Advantages and Selection Notes

The VTD24SA offers a compact fixed 24 V DC output, 5 A rated current, overcurrent and overvoltage protection, wide DC input compatibility, convection cooling and simple module mounting. Related VTD-SA models provide 5 V, 12 V, 15 V and 48 V outputs for other supply requirements. When selecting a replacement, confirm input voltage and phase, output voltage and current, adjustment range, protection needs, mounting space and environmental rating. The VTD24SA is an AC-DC power supply, not a battery charger, inverter, UPS, servo drive or field sensor; its role is to convert AC line power into regulated 24 V DC for control and electronic loads.


Get a Quote