Description
MTL 3042: MTL3042 Loop-Powered DC Isolator Product Description
Brand and Product Identification
The MTL 3042, also designated MTL3042, is a one-channel loop-powered DC isolator from the MTL intrinsically safe interface product range, now associated with Eaton Crouse-Hinds MTL process safety products. The MTL3042 is a 4 to 20 mA signal isolator designed primarily for isolating and passing a 4/20 mA control signal from a safe-area controller to a current-to-pressure, or I/P, converter or position actuator in a hazardous area. It belongs to the MTL3000 family of intrinsically safe isolators and replaces direct hard-wired 4 to 20 mA loops between controller and field device with an isolated interface module.
Product Function and Operating Principle
The MTL3042 acts like a direct-current transformer. It is always powered from the safe-area side and ensures that the same current flows in both the safe-area and hazardous-area circuits while allowing the signal to be controlled from either side. The module repeats the 4 to 20 mA analog current signal across the isolation barrier, maintaining loop continuity and preventing ground loops or common-mode voltage transfer between controller and field transmitter or actuator. It is intended mainly for I/P converter or position actuator drive loops rather than for digital signal transmission.
Electrical and Signal Specifications
The MTL3042 accepts an input voltage of 11 to 35 V DC. The input and output signal range is 4 to 20 mA. Minimum output voltage at 20 mA follows the output voltage versus input voltage characteristic shown in the datasheet, while maximum output voltage is 28 V from a 300 Ω load. Input and output circuit ripple is below 100 µA peak to peak. Transfer accuracy at 20 degrees Celsius is better than 50 µA, and temperature drift is below 2 µA per degree Celsius. Response time settles to within 10 percent of final value after typically 70 ms.
Power Dissipation and Fuse
Power dissipation within the MTL3042 unit is typically 0.4 W at 24 V with a 20 mA signal, and maximum 0.5 W at 35 V with a 20 mA signal. The module includes a replaceable fuse rated 50 mA, 5 by 20 mm glass cartridge to DIN 41571 sheet 2, semi-time-lag, type M. The fuse protects the loop circuit and should be replaced with the specified rating during maintenance.
Intrinsic Safety Parameters
The MTL3042 safety description is 28 V, 300 Ω, 93 mA, with Um equal to 250 V RMS or DC. FM maximum entity parameters are Voc equal to 28 V, Isc equal to 93 mA, Ca equal to 0.13 µF and La equal to 4.0 mH. The I/P converter location may be Zone 0, Group IIC, T4 to T6 hazardous area if suitably certified, or Division 1, Group A hazardous location. The actual hazardous-area approval, gas group and temperature class must be verified against the relevant certificate for the installed unit.
Mechanical Construction and Terminals
The MTL3042 is a compact DIN-rail mounted interface module with a weight of 160 g. Terminals separate the safe-area side and hazardous-area side in the module wiring diagram: safe-area controller connections and hazardous-area I/P converter or actuator connections are grouped according to the MTL3042 schematic. The module uses screw or plug-in field terminals typical of the MTL3000 isolator family, and mounting follows the standard MTL rail installation arrangement. Field wiring should be routed with separate safe-area and hazardous-area cable runs as required by the intrinsic safety installation standard.
Typical Application Scenarios
Typical applications include 4 to 20 mA control loops driving I/P converters, pneumatic valve positioners, current-to-pressure transducers or position actuators in oil and gas, chemical, petrochemical, pharmaceutical, power and process industries with classified hazardous areas. The isolator is used where a controller output signal must be isolated from the field device, where ground loops must be avoided, or where intrinsic safety barriers are required between safe-area control equipment and hazardous-area instrumentation.
Installation and Wiring Notes
Installation and commissioning should follow the MTL3042 datasheet, MTL3000 common specification and local intrinsic safety wiring codes. Confirm supply loop voltage, signal range, load resistance, entity parameters and certificate approval before connecting the I/P converter. The safe-area controller side and hazardous-area field side must be wired to the designated terminals, and cable parameters must remain within the Ca and La limits. Grounding, shielding and separation should follow the site intrinsic safety installation practice. Maintenance should include checking terminal tightness, loop current, fuse condition and module status.
Advantages and Selection Notes
The MTL3042 offers one-channel loop-powered isolation, 4 to 20 mA signal repetition, low transfer error, fast response, intrinsic safety entity parameters and compact MTL3000 DIN-rail mounting. For loops sensitive to the volt drop introduced by this unit, the separately powered MTL3045 should be considered. In many closed-loop applications with integral control where lower accuracy is acceptable, the lower-cost MTL3043 can also drive I/P converters. The MTL3042 is an analog signal isolator, not a transmitter, controller, power supply, safety relay or field actuator; its role is to safely repeat and isolate a 4 to 20 mA control current between safe-area and hazardous-area circuits.
Get a Quote