3. Product Specification Manual

3.1 Basic Parameters

• Part Number: P0914YZ

• Corresponding Model: FCM2F2 Fiber Optic Fieldbus Extender

• Manufacturer: Foxboro (AVEVA / Schneider Electric)

• Applicable System: I/A Series & Evo DCS Distributed Control System

• Core Function: Electrical-to-optical fieldbus signal conversion, long-distance bus extension, EMI isolation

• Input Power: 24VDC (21.6V ~ 25.2V wide regulated voltage)

• Typical Power Consumption: ≤3.5W

• Protection Class: IP20

• Housing Material: Die-cast aluminum alloy

• Net Weight: 0.48kg

• Max Fiber Transmission Distance: 2km (single mode fiber)

• Compatible Matching Hardware: P0914WP controller, P0914XA/XB/XG backplane, all FBM analog/digital I/O modules

3.2 Communication & Optical Performance

• Internal Bus Rate: 2Mbps differential redundant fieldbus

• Optical Interface: Dual single-mode fiber ports (transmit / receive separate channels)

• Redundancy Mode: Dual optical channel hot standby master-slave redundancy

• Fault Switching Performance: Zero-data-loss seamless link switching

• Isolation Performance: Complete electrical isolation between local cabinet and remote cabinet via fiber, fully suppress EMI and ground loop noise

• Supported Bus Topology: Daisy chain, star and mixed cabinet expansion topology

• Optical Power Detection: Built-in real-time optical signal strength monitoring function

3.3 Maintenance & Self-Diagnosis Features

• Hot Swap Support: Online plug-and-play without cutting off cabinet power supply

• On-board Diagnosis: Real-time detection of fiber disconnection, insufficient optical power, bus communication loss, module overvoltage; LED visual status prompt

• Data Verification: Built-in cyclic redundancy check (CRC) algorithm to avoid distorted transmission data

• Configuration Compatibility: Fully compatible with official I/A Series system configuration software for redundant link parameter setup

3.4 Environmental Technical Index

• Operating Temperature: 0℃ ~ +60℃

• Storage Temperature: -40℃ ~ +85℃

• Ambient Adaptability: ISA S71.04 Class G3 harsh dust resistance, compliant with IEC industrial EMC anti-interference standards

• Vibration Resistance: Meet IEC60068 international industrial anti-vibration test specifications

• Relative Humidity: 5% ~ 95% non-condensing

• Altitude Adaptability: Operating altitude -300m ~ 3000m; storage altitude -300m ~ 12000m

• Industrial Certifications: CE, UL industrial safety certification

3.5 Built-in Safety Protection Circuit

1. Reverse power connection prevention circuit

2. Overvoltage, overcurrent and short-circuit automatic power-off protection

3. Optical port static surge anti-interference protection

4. Over-temperature automatic power limiting protection to prevent module burnout

3.6 Step-by-Step Installation Instructions

1. Vertically install P0914YZ into the dedicated slot of P0914 series backplane inside standard 19-inch industrial control cabinet;

2. Connect 24VDC regulated DC power supply and strictly distinguish positive and negative polarities;

3. Insert single-mode fiber jumpers into the transmit and receive optical ports on the module front panel, connect the other end to the FCM2F2 extender of the remote control cabinet;

4. Lock all fiber connectors to avoid light attenuation caused by loose contact;

5. Power on the cabinet, launch I/A Series configuration software and activate the fiber redundant link function;

6. Check front panel LED indicators: steady green = normal dual optical channel communication, flashing red = fiber breakage or insufficient optical power.

4. Application Fields

1. Petrochemical, crude oil refining and natural gas processing plants (distributed workshop remote cabinet interconnection)

2. Fine chemical, pharmaceutical and basic chemical raw material production bases

3. Large thermal power plants, hydropower stations, wind and photovoltaic new energy power stations

4. Steel smelting, non-ferrous metal metallurgy and heavy industry factories with large electromagnetic noise

5. Cement rotary kiln, building material calcination and coal mineral processing plants

6. Pulp, papermaking, textile and large-scale food manufacturing industrial parks

7. Municipal waste incineration power plants, regional sewage treatment environmental protection bases

8. Large industrial park central heating stations, distributed HVAC heat exchange control systems

Information Verification Note

• Confirmed fixed facts: P0914YZ = FCM2F2 fiber fieldbus extender, 2km single-mode fiber transmission, dual redundant optical channels, electrical isolation via fiber, hot swappable, compatible with full P0914 backplane series, ISA G3 dust resistant.

• Unverified content: Original factory complete optical power calibration test report, customized multi-mode fiber adaptation parameters, third-party protocol expansion driver specifications, which require official Foxboro original manual for cross-verification.