1. General Introduction

2. Common Model Code Definition

• MDX61B: MOVIDRIVE B series, equipped with dual expansion slots for encoder and fieldbus modules

• Power code: Indicates rated power (30 kW / 37 kW / 45 kW / 55 kW / 75 kW etc.)

• 503: 3-phase 380–500 V AC, no integrated EMC filter (external EMC filter required)

• 4: Integrated brake chopper, supports four-quadrant regenerative operation

• 0T: Conformal coated PCB for harsh working conditions

3. Shared Technical Features

Electrical Performance

• Input Voltage: 3×380–500 V AC (-15% ~ +10%), 50/60 Hz

• Output Frequency Range: 0–400 Hz

• Control Modes: V/f control, VFC vector control, CFC closed-loop vector control, servo control

• Overload Capability: 150% rated current for 60 s; 175% rated current for 2 s

• Switching Frequency: 4 kHz, 8 kHz, 12 kHz, 16 kHz (adjustable)

• Safety Function: STO (Safe Torque Off), compliant with PL d / SIL 2

Mechanical & Environmental Requirements

• Protection Class: IP20 (cabinet installation only)

• Operating Temperature: 0 °C to +40 °C; power derating is required above 40 °C

• Storage Temperature: -25 °C to +70 °C

• Altitude: No power derating below 1000 m; derate 1% per additional 100 m above 1000 m

• Certifications: CE, UL, RoHS, EAC

4. Core Advantages of 0T Version

1. Enhanced environmental adaptability: Conformal coating isolates the circuit board from humidity, dust and mild corrosive substances, effectively extending service life.

2. Stable operation: Reduces failure risks caused by condensation and dirt accumulation in tough workshops.

3. Consistent performance: Same electrical performance, control functions and expandability as standard 00 models.

4. Four-quadrant operation: Built-in brake chopper realizes regenerative braking and energy recovery.

5. Modular expansion: Compatible with optional encoder and various fieldbus modules.

6. Integrated motion control: IPOSplus® system supports positioning, electronic gearing and master-slave synchronization.

5. Installation & Wiring Rules

• Mounting: Install vertically inside a control cabinet.

• Ventilation Clearance: Reserve minimum 100 mm space at top and bottom, 50 mm on both sides.

• Main Terminals:

  • X1: Mains connection (L1, L2, L3, PE)

  • X2: Motor connection (U, V, W, PE)

  • X4: DC link terminals for external brake resistor

  • X11: Analog input (0–10 V / 4–20 mA)

  • X13: 24 V DC digital inputs and outputs

  • X15 / X16: Encoder interfaces

• Note: External EMC filter must be installed to meet electromagnetic compatibility standards. Use shielded cables for motor and signal wiring.

6. Operation & Maintenance

• Local operation: Use DBG60B handheld keypad for parameter setting, manual operation and fault checking.

• PC commissioning: Use MOVITOOLS® MotionStudio for program editing, real-time monitoring and fault diagnosis.

• Routine maintenance: Regularly check cable connections and ventilation paths; clean dust with dry compressed air.

• Typical faults: Overcurrent (OC), Overvoltage (OV), Overtemperature (OT), Encoder Error. Fault information can be read via keypad or software.

7. Applicable Scenarios

• Industrial sites with high humidity, heavy dust or mild corrosive atmosphere

• Conveyors, cranes, hoists, textile machinery, woodworking equipment, large fans and pumps

• Production lines operating in non-standard clean workshop environments

8. Version Comparison

• 00: Standard non-coated PCB, for clean and dry indoor environments

• 0T: Conformal coated PCB, for humid, dusty or mildly corrosive harsh environments

• 50: Special factory customized version with exclusive firmware and settings