1. General Information

• Model: CP033/Y

• Manufacturer: KEBA AG (Austria)

• Type: KeControl C3 Series CPU Module (for injection molding, robotics, industrial automation)

• Order No.: 002179

• Mounting: KEBA K2 / C3 rack, DIN rail compatible

• Protection Class: IP20 (module), front panel IP65 (HMI variant)

• Weight: approx. 1.2 kg

• Dimensions: approx. 120 × 80 × 40 mm (W×H×D)

2. Electrical Specifications

• Operating Voltage: 24 V DC (±10%) (powered by RS‑091/A)

• Current Consumption: ≤ 1.5 A

• Processor: High‑performance ARM embedded CPU

• Memory: Flash 128 MB, RAM 64 MB, non‑volatile storage for programs/recipes

• Real‑Time Clock (RTC): Integrated, battery‑backed

• Protection: Overvoltage, short‑circuit, ESD, reverse polarity

• Isolation: 500 V AC (channel‑to‑bus)

3. Communication Interfaces

• Ethernet: 10/100 Mbps (TCP/IP, EtherCAT, Modbus TCP)

• CANopen: For servo drives (e.g., KEBA ServoC series) and I/O modules

• USB 2.0: Data transfer, HMI connection, firmware update

• Serial: RS‑232/485 (optional)

• Backplane Bus: KEMRO K2 bus (compatible with SC‑102, PD‑242/A)

4. Key Functions

1. Real‑Time Control: Sampling time down to 500 µs; ideal for motion & hydraulic control

2. Motion Control: Up to 8 axes (CANopen/EtherCAT); synchronized motion for robots/injection machines

3. Integrated HMI: 7” TFT touch display (500 cd/m²); resistive touch for glove operation

4. Diagnostics: LED status (Power, Run, Fault), overcurrent/short‑circuit detection, error logging

5. Hot‑Swap: Replace module without system shutdown (K2 CPU supported)

6. Programming: KEBA KAS IDE (Automation Suite); unified programming for logic, motion, HMI

5. Environmental Conditions

• Operating Temperature: 0 °C … +55 °C

• Storage Temperature: −40 °C … +85 °C

• Relative Humidity: 5 % … 95 % RH (non‑condensing)

• Altitude: ≤ 2000 m

• Pollution Degree: 2

6. Compatibility

• Systems: KEBA K2 / C3, injection molding machines, CNC, robotic cells

• Power Supply: RS‑091, RS‑091/A (24 V DC)

• I/O Modules: SC‑102 (digital/analog), PD‑242/A (backplane)

• HMI: KeTop series, CP033/Y integrated display

7. Installation & Wiring

1. Disconnect 24 V DC before installation.

2. Insert module into K2/C3 rack and lock firmly.

3. Connect 24 V DC (RS‑091/A) to power terminals.

4. Wire Ethernet/CAN/USB to controller, HMI, and drives.

5. Separate power and signal cables to avoid interference.

6. Power on; check Power LED ON and Fault LED OFF.

8. Safety Instructions

• Install/service only by qualified electrical technicians.

• Do not open/modify the module; voids warranty and risks electric shock.

• Operate only within 24 V DC, 0–55 °C rated range.

• Ensure adequate ventilation; do not block cooling vents.

• Replace if damaged, overheated, or insulation fails.

9. Certifications

• CE (EN 61000‑6‑2, EN 61000‑6‑4)

• UL 508

• RoHS compliant