8BVI0055HWD0.000-1 Detailed Product Description

1. Product Overview

2. Basic Product Information

• Part Number: 8BVI0055HWD0.000-1

• Product Series: ACOPOSmulti

• Type: Dual-axis Inverter Module, High Voltage, Wall Mount

• Rated Current: 7.6 A per axis

• Installation Type: Wall mounting

• Expansion Slots: 2 slots for ACOPOSmulti option modules

• Integrated Functions: Safe stop, uncontrolled standstill, motor brake interface, motor temperature sensor interface, Dynamic Node Assignment (DNA)

• Certifications: CE, UKCA, cULus, KC, Functional Safety Certification

3. Electrical Specifications

3.1 DC Bus Power

• Rated DC Bus Voltage: 750 VDC

• Operating Voltage Range: 315 VDC ~ 800 VDC

• Total Continuous Power Loss: 11.19 kW

• Internal Bus Capacitance: 330 µF

3.2 24 VDC Auxiliary Supply

• Nominal Input Voltage: 25 VDC ±1.6%

• Internal Input Capacitance: 23.5 µF

• Max Power Consumption: 16 W + slot load + 24V output load + brake power consumption

• Built-in 24 VDC Output: 2 channels

• Output Regulation: 24 VDC ±6% under 315–800 VDC bus; proportional output under 260–315 VDC

• Electronic Fuse: 250 mA, slow blow, auto-reset

3.3 Motor Drive Parameters (Per Axis)

• Continuous Output Power: 5.5 kW

• Continuous Output Current: 7.6 Aeff

• Peak Output Current: 18.9 Aeff

• Switching Frequency: Default 5 kHz (no derating); optional 10 kHz / 20 kHz

• Max Output Frequency: 598 Hz

• Motor Cable Length:

  • 5 kHz / 10 kHz: Max 25 m

  • 20 kHz: Max 10 m

• Altitude Derating: Above 500 m altitude, derate 0.76 Aeff per 1000 m

• Insulation Class: Compliant with IEC TS 60034-25:2004 Class A

3.4 Motor Brake Interface (2 Channels)

• Output Voltage: 24 VDC +5.8% / -0%

• Continuous Current per Channel: 1.1 A

• Max Internal Resistance: 0.5 Ω

• Demagnetization Voltage: Approx. 30 V

• Max Demagnetization Energy: 1.5 Ws

• Max Switching Frequency: 0.5 Hz

• Protection: Overload, short circuit, open circuit and under-voltage monitoring

3.5 Control & Digital Inputs

• Enable Inputs: 4 channels (2 per axis), Sink type, 24 VDC

• Trigger Inputs: 2 channels, Sink type 24 VDC

• Temperature Sensor Interface: 2 channels, compatible with 500 Ω ~ 5 kΩ resistive sensors

• Standby Power Consumption: 8.8 W

4. Mechanical Specifications

• Dimensions (W × H × D): 53 mm × 317 mm × 263 mm

• Weight: Approx. 2.9 kg

• Protection Class: IP20 (EN 60529)

• Pollution Degree: Class 2

• Overvoltage Category: Class III

5. Environmental Conditions

5.1 Temperature

• Operating Temperature: +5 °C ~ +40 °C rated; up to +55 °C with derating

• Storage Temperature: -25 °C ~ +55 °C

• Transport Temperature: -25 °C ~ +70 °C

5.2 Humidity

• Operating Humidity: 5% ~ 85% RH, non-condensing

• Storage Humidity: 5% ~ 95% RH, non-condensing

• Transport Humidity: Max 95% RH at 40 °C, non-condensing

5.3 Installation & Altitude

• Allowed Mounting: Vertical upright, horizontal front side up

• Not Allowed: Horizontal side mounting

• Rated Altitude: 0 ~ 500 m

• Max Operating Altitude: Up to 4000 m (with current derating)

6. Interface & Terminal Definition

• X1: Control interface, enable and brake signal terminals

• X2: 24 VDC auxiliary power input and output

• X3A / X3B: Encoder interface for option modules

• X4A / X4B: Motor brake and temperature sensor connection

• X5A / X5B: Motor power terminals U / V / W / PE

7. LED Status Indication

• RDY Green: Module ready / fault standby

• RUN Orange: Power stage enabled, axis running

• ERR Red: System fault, overload, short circuit or temperature alarm

• POWERLINK LED: Link and communication status

• 24V Green: Auxiliary power supply normal

8. Protection Functions

• Overcurrent, short circuit and earth fault protection

• IGBT and heat sink over-temperature protection

• DC bus over-voltage / under-voltage protection

• 24 VDC auxiliary supply under-voltage monitoring

• Built-in Safe Stop and safety standstill function

• Motor brake overload, open circuit and fault detection

9. Typical Applications

• CNC machine tools and machining centers

• Automated production and assembly lines

• Packaging, printing and textile machinery

• Logistics conveying and positioning systems

• Multi-axis synchronous control, electronic gear and high-precision motion control systems