2. Part Number & Revision

• Model: 51304672100 (short: 51304672-100)

• Hardware: HDW E1

• Revision: D

• Firmware: D 4‑05‑084‑6568

• Weight: approx. 660–665 g

• Dimensions: 320 × 30 × 280 mm

3. Technical Specifications

• Number of Channels: 8 isolated analog outputs

• Output Signals:

  • Current: 4–20 mA (sink/source)

  • Voltage: 0–10 V

• Accuracy: ±0.1% FS (25 °C)

• Resolution: 16‑bit

• Load Capacity:

  • Current: ≤ 600 Ω

  • Voltage: ≥ 1 kΩ

• Isolation: Channel‑to‑channel & channel‑to‑bus isolation

• Power Supply: 24 VDC (from system backplane)

• Operating Temperature: 0 °C to +60 °C

• Storage Temperature: −40 °C to +85 °C

• Certifications: CE, RoHS, UL (industrial control)

4. Key Features

• 8‑channel high‑precision analog output for process control.

• Robust industrial design for harsh environments.

• Seamless integration with Honeywell DCS & control systems.

• Short‑circuit & overload protection per channel.

• LED status indicators for power, run, fault.

• DIN rail / panel mount compatible.

5. Applications

• Honeywell DCS (e.g., TDC3000, Experion) analog output subsystem.

• Process industries: chemical, petrochemical, power, water treatment.

• Industrial automation: manufacturing lines, HVAC, building control.

• Precision control of valves, actuators, motor drives, transmitters.

6. Installation & Wiring

1. Mounting: Install on standard DIN rail or control panel; ensure adequate ventilation (≥ 50 mm clearance).

2. Backplane Connection: Insert module into Honeywell I/O rack; secure with locking screws.

3. Field Wiring:

   • Use shielded twisted‑pair (STP) cable (22–18 AWG).

   • Connect shield to earth ground at one end only (control room side) to avoid ground loops.

   • Terminate per channel: +/− for current/voltage output.

4. Wiring Precautions:

   • Separate analog cables from high‑voltage power cables (≥ 30 cm).

   • Avoid parallel routing with AC power lines.

7. Maintenance & Troubleshooting

• Routine Inspection: Check for loose connectors, physical damage, or corrosion.

• LED Status:

  • PWR (Green): On = power OK.

  • RUN (Green): Blinking = normal operation.

  • FLT (Red): On = fault (short circuit, overload, communication error).

• Cleaning: Use dry cloth; avoid liquid cleaners.

• Replacement: Use only Honeywell original parts; power off before removal/insertion.

8. Safety Precautions

• Electrical Safety: Disconnect all power before installation/wiring/maintenance.

• Environmental: Do not expose to moisture, dust, or corrosive gases beyond rated limits.

• Modification: Do not alter module hardware or firmware; use Honeywell‑approved replacements only.

9. Ordering Information

• Part Number: 51304672100 (51304672-100)

• Description: Honeywell 8‑Channel Analog Output Module, HDW E1, Rev D

• Compatible Systems: Honeywell DCS, Experion, TDC3000 & related I/O racks

Note: This is a consolidated English specification based on Honeywell public data and industrial distributor documentation. For the official Honeywell datasheet, contact your local Honeywell representative or visit the official website.

Honeywell 51304672100 Instruction Manual

1. Product Overview

2. Basic Parameters

3. Main Features

1. High precision and stable signal transmission

2. Independent overcurrent and short circuit protection for each channel

3. LED indicators display power, running and fault status

4. Standard rack installation, easy assembly and replacement

5. Good anti-interference performance, adapt to harsh industrial environment

6. Compliant with CE, RoHS and UL industrial safety standards

4. Application Scope

5. Installation Instruction

1. Cut off system power before installation and disassembly.

2. Insert the module into designated position of I/O rack and fix locking device.

3. Adopt shielded twisted pair cable for field wiring.

4. Keep analog wire away from high voltage power cable, separation distance no less than 30cm.

5. Ground cable shield only at control cabinet side to prevent ground loop.

6. Indicator Description

7. Maintenance Rules

1. Regularly check connector tightness and module surface damage.

2. Clean dust with dry cloth, do not use corrosive liquid.

3. Stop operation immediately once fault alarm appears.

4. Only original Honeywell spare parts can be used for replacement.

8. Safety Notice

1. All wiring and maintenance work must be carried out under power-off state.

2. Do not use beyond rated temperature and load range.

3. Do not disassemble or modify internal structure of the module.

4. Avoid damp, dusty and corrosive working environment.