RELIANCE 61C-366 4-channel isolated voltage-type analog output rail module
61C-366 is a 4-channel isolated voltage-type analog output rail module under Reliance AutoMate 61C series distributed I/O lineup, matching AutoMate 15E/20/20E PLC control system. It converts digital control commands from main controller into standard 0~10VDC analog voltage signals to drive proportional valves, servo drivers and variable-speed actuators. Original production has been discontinued; available commodities include surplus unused original stock and fully load-tested refurbished modules for spare replacement of legacy papermaking, metallurgy and chemical old automation control cabinets.
Description
Product Introduction
61C-366 is a 4-channel isolated voltage-type analog output rail module under Reliance AutoMate 61C series distributed I/O lineup, matching AutoMate 15E/20/20E PLC control system. It converts digital control commands from main controller into standard 0~10VDC analog voltage signals to drive proportional valves, servo drivers and variable-speed actuators. Original production has been discontinued; available commodities include surplus unused original stock and fully load-tested refurbished modules for spare replacement of legacy papermaking, metallurgy and chemical old automation control cabinets.
Model Definition
61C = Reliance standard remote rail-mounted I/O series code; 366 is exclusive specification code for 4-channel 0~10VDC voltage output, 12-bit DA conversion and split terminal layout. Distinguished from 61C-365 (4~20mA current output) only on analog output signal type while sharing identical rail installation structure and bus communication protocol.
Technical Specifications
Auxiliary power supports dual input: 120VAC 50/60Hz or 20~32VDC, typical working current 340mA@24VDC. Analog output range fixed at 0~10VDC, 12-bit conversion precision, maximum single-channel load resistance ≥2kΩ. Working ambient temperature: -20℃ ~ +55℃, storage temperature: -40℃ ~ +85℃, applicable humidity 5%~95% non-condensing. Front panel embedded replaceable 250V rated fuse for overcurrent protection, panel-mounted overall dimension consistent with 61C-365 series standard size, conforms to UL industrial safety certification.
Interface and Communication Configuration
Rear dedicated rail bus interface connects to AutoMate local head or main controller via proprietary rail cable for backplane bus data exchange with CPU. Front side adopts detachable 12-pin split screw terminal block, four output channels separately grouped with three terminals per channel for 0~10VDC signal wiring and auxiliary power access. Two front-panel LED indicators: PWR OK for power supply status, COM OK for bus communication running status; built-in toggle switch to switch between local head mode and distributed remote rail working mode, no onboard RS485/Modbus universal communication port reserved.
Core Functions
Receive digital setpoint data from upper AutoMate PLC via dedicated rail bus, execute digital-to-analog conversion to output stable 0~10VDC analog voltage for field closed-loop actuator regulation. Real-time monitor each channel short-circuit and overload fault, upload abnormal fault codes to main control unit and trigger corresponding status indication. Four channels adopt independent isolation circuit to block field voltage surge interference from intruding main PLC control system. Supports mixed installation with digital DI/DO modules and current-type AO modules on the same field rail for flexible collocation of scattered field control points.
Application Scenarios
Mainly applied to occasions requiring 0~10VDC voltage control: papermaking roller speed proportional regulation, metallurgical furnace air door actuator positioning control, chemical pipeline electric regulating valve drive, printing equipment hydraulic proportional valve signal output and textile oven fan speed adjustment. Widely used for decentralized remote I/O reconstruction of outdated production lines far away from central control cabinet.
Operation and Maintenance Instructions
Cut off all AC/DC power supply of module and wait over 15 minutes for internal capacitor residual electricity discharge before disassembly or terminal wiring modification. Conduct semi-annual maintenance: check terminal fastening status and pin oxidation, remove internal dust with dry low-pressure compressed air. Strictly control field load impedance above rated minimum value to avoid long-term low-impedance overload. When abnormal output appears, firstly troubleshoot external field wiring and actuators; replace the whole 61C-366 module only after eliminating all peripheral circuit faults.
Get a Quote